Optimizing Material Selection and Manufacturing Processes For Enhanced Drill Bit Performance
Keywords:
Drill Bit, Manufacturing Processes, Material Selection, Optimizing, Tool DurabilityAbstract
Drill bit performance is significantly influenced by material selection and manufacturing processes. This study optimizes material choices and advanced manufacturing techniques to enhance drill bit performance. By evaluating mechanical properties, wear resistance, and thermal stability of various materials, the research identifies the most suitable options for specific drilling conditions. Additionally, the impact of advanced manufacturing methods, such as additive manufacturing and precision machining, is explored to improve accuracy, durability, and efficiency. The results demonstrate improvements in drill bit performance, including reduced wear and extended operational lifespan. This research contributes to the development of more efficient and durable drill bits.References
R. Hari Nath Reddy, M. Alphonse, V. K. Bupesh Raja,
K. Palanikumar, D. R. Sai Krishna Sanjay, and K. V
Madhu Sudhan, “Evaluating the wear studies and tool
characteristics of coated and uncoated HSS drill bit –
A review,” Mater. Today Proc., vol. 46, pp. 3779–
, 2021, doi:
https://doi.org/10.1016/j.matpr.2021.02.022.
L. Singh and A. Yadav, “Modelling & Analysis of Drill Bit with different Materials,” Int. Res. J. Eng.
Technol., pp. 194–199, 2019, [Online]. Available:
www.irjet.net
Y. Zhang, H. Sogn, M. Cai, and R. Santana, “An
Additive Manufacturing Process Enables the 3D-
Printed Application of Armors for Drill Bits,” May 23,
doi: 10.2118/214548-MS.
H. Gökçe and İ. Çiftçi, “Innovative hybrid drill bit that
accelerates heat conduction: Its design, manufacturing
and test,” J. Manuf. Process., vol. 120, pp. 353–364,
, doi:
https://doi.org/10.1016/j.jmapro.2024.04.006.
H. H. Hassanalideh and S. Gholampour, “Finding the
optimal drill bit material and proper drilling condition
for utilization in the programming of robot-assisted
drilling of bone,” CIRP J. Manuf. Sci. Technol., vol.
, pp. 34–47, 2020, doi:
https://doi.org/10.1016/j.cirpj.2020.09.011.
Peparpenas, “Technical Handbook,” no. November,
pp. 1–19, 2022.
B. Nur Prasetyo, “Analisis Kekerasan Pada Mata Bor
Berbahan Baja High Speed Steel Hasil Proses
Hardening Dengan Pendinginan Oli Dan Coolant,”
Presisi, vol. 25, no. 1, pp. 1–9, 2023.
Y. Gao, H. Xiao, B. Liu, and Y. Liu, “Enhanced
drilling performance of impregnated diamond bits by
introducing a novel HEA binder phase,” Int. J.
Refract. Met. Hard Mater., vol. 118, p. 106449, 2024,
doi: https://doi.org/10.1016/j.ijrmhm.2023.106449.
J. Guignard, M. Prakasam, and A. Largeteau, “A
Review of Binderless Polycrystalline Diamonds:
Focus on the High-Pressure-High-Temperature
Sintering Process,” Materials (Basel)., vol. 15, no. 6,
, doi: 10.3390/ma15062198.
L. Y. Ropyak, T. O. Pryhorovska, and K. H. Levchuk,
“Analysis of materials and modern technologies for
PDC drill bit manufacturing,” Prog. Phys. Met., vol.
, no. 2, pp. 274–301, 2020.
M. Yavuz, H. Gökçe, İ. Çiftçi, H. Gökçe, Ç. Yavaş,
and U. Şeker, “Investigation of the effects of drill
geometry on drilling performance and hole quality,”
Int. J. Adv. Manuf. Technol., vol. 106, no. 9, pp. 4623–
, 2020, doi: 10.1007/s00170-019-04843-3.
V. Vignesh, S. Satish, V. Gopi, J. Jishnoop, and G. A.
Menon, “Comparison of coated and uncoated HSS
drill bit on surface roughness, material removal rate
and dimensional accuracy of SS410 stainless steel,”
Mater. Today Proc., vol. 58, pp. 13–19, 2022, doi:
https://doi.org/10.1016/j.matpr.2021.12.307.
A. Saai et al., “Adaptation of Laboratory tests for the
assessment of wear resistance of drill-bit inserts for
rotary-percussive drilling of hard rocks,” Wear, vol.
–457, no. May, pp. 1–10, 2020, doi:
1016/j.wear.2020.203366.
