PENANGANAN PENGURANGAN JUMLAH DOWNTIME BERLEBIH DARI UNIT ABC 1 DENGAN PENDEKATAN LEAN MAINTENANCE PADA PT. XYZ

Aditya Hendi Prakoso, Nina Aini Mahbubah

Abstract


PT. XYZ is a manufacturing company that operates in the field of fertilizer and non-fertilizer production with the aim of helping the country realize a food self-sufficiency program. It is known that PT. XYZ has problems with excessive machine downtime in its production process. Problems occur because there is repeated damage to the machine, activities that involve waste, so that the maintenance system on one machine has not been carried out optimally. The aim of this research is to analyze maintenance activities implemented in the Company and then minimize waste in maintenance activities using a lean maintenance approach. Downtime data collection was carried out in April 2024, then data processing was carried out using equipment effectiveness to see how effective the existing equipment was, then continued with Maintenance Value Stream Mapping (MVSM) to find out waste that occurred during the maintenance process, after the cause of the waste. is known, several suggested options are given to minimize the waste that occurs. From the implementation of the recommendations made, the machine equipment effectiveness value increased from 92% to 97%, the maintenance effectiveness value increased from 41.6% to 66.7%.

Full Text:

PDF

References


T. I. Agro dan P. A. T. I. Makassar, “Identifikasi Perawatan Mesin Pemberi Pakan Dengan Metode Maintenance Value Stream Mapping ( Mvsm ) Pada Perusahaan Pakan Ternak,” hal. 121–126, 2023.

H. Prisilia dan D. A. Purnomo, “Pendekatan Konsep Lean Untuk Meminimalisir Waste Pada Pemeliharaan Pompa (Studi Kasus: PDAM Tirta Banyuwangi),” J. Tecnoscienza, vol. 8, no. 1, hal. 117–131, 2023.

P. Studi, T. Industri, dan U. Tarumanagara, “PENERAPAN LEAN MAINTENANCE PADA AKTIVITAS PERAWATAN MESIN UNTUK MINIMASI WASTE” vol. 1, no. 1, hal. 73–83, 2022.

Rochmoeljati, Muhammad Irza Firmansyah, dan Isna Nugraha, “Analisa Tingkat Waste Pada Bagian Perawatan Dengan Metode Lean Maintenance Untuk Meminimumkan Waste Di Pt. Varia Usaha Beton Gresik,” Waluyo Jatmiko Proceeding, vol. 15, no. 1, hal. 210–218, 2022, doi: 10.33005/waluyojatmiko.v15i1.46.

H. A. Iskandar, F. J. Daywin, dan J. Kristina, “PENERAPAN LEAN MAINTENANCE PADA PRODUKSI COLD PRESSED JUICE DALAM MENGURANGI DOWNTIME MESIN PADA PT . HOM KULINARI JAYA” vol. 1, no. 1, hal. 84–93, 2022.

J. ’ In dan R. E. Nugroho, “Analysis of the Application of Lean Maintenance to Optimize Transformer Maintenance Duration at MRO Company PT. Servo Indonesia Perkasa,” Ijevss, vol. 03, no. 03, hal. 2024, 2024.

S. Stevan Wijaya, D. N. Prayogo, dan M. A. Hadiyat, “Perancangan dan Penerapan Lean Maintenance Management di PT. Hapete,” Calyptra J. Ilm. Mhs. Univ. Surabaya, vol. 7, no. 2, hal. 4855–4872, 2019.

P. D. Karningsih, W. Puspitasari, dan M. L. Singgih, “Cost-Integrated Lean Maintenance to Reduce Maintenance Cost,” J. Optimasi Sist. Ind., vol. 22, no. 1, hal. 69–80, 2023, doi: 10.25077/josi.v22.n1.p69-80.2023.

W. Azhari, M. A. adi, A. C. Dewi, dan H. Mahfud, “Hoist Tulangan Machine Maintenance Design Using Lean Maintenance Method (Case Studi Of Pt. Xyz),” IOP Conf. Ser. Mater. Sci. Eng., vol. 1125, no. 1, hal. 012111, 2021, doi: 10.1088/1757-899x/1125/1/012111.

J. R. Díaz-Reza, J. L. García-Alcaraz, C. Sánchez-Ramírez, dan A. R. Vargas, “Assessing the impact of Lean manufacturing on the Social Sustainability through Structural Equation Modeling and System Dynamics,” Jordan J. Mech. Ind. Eng., vol. 18, no. 1, hal. 113–130, 2024, doi: 10.59038/jjmie/180109.




DOI: https://doi.org/10.33373/sigmateknika.v7i2.7001

Refbacks

  • There are currently no refbacks.





E-ISSN 2599-0616

 

This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

 

Sigma Teknika

Gedung Lt.1 Kampus Universitas Riau Kepulauan Batam

Jl. Batu Aji Baru No.99 Batu Aji

Email: sigmateknika@journal.unrika.ac.id

 

 

Web Analytics