ANALISA UMUR ALAT POTONG MESIN MILLING DENGAN MATERIAL SUS 420
Abstract
This research was performed on 3 cutting tools which are tool drill 1.8mm, 2.5mm in diameter and tool back chamfer 2.2mm in diameter. Hardness value from each cutting tool was approximately 300 HRC. Meanwhile, material used in this research is SUS 420 that has hardness value 262HRC. To perform cutting on work unit, it was requested higher hardness value for cutting tool compared to work unit (SUS420). Tool drill 1.8mm in diameter was used at first pitting process (rapping), tool drill 2.5mm in diameter was used at second pitting process (finishing) and tool back chamfer 2.2mm in diameter was used at the last pitting process. This research was performed to define the tool life of cutting tools that utilized in milling machine from work unit material SUS 420. From this research, it was expected maximum amount that can be achieved from cutting tools every replacement can be obtained. At the end of study, when the replacement time of cutting tools can be defined, the loss of not good product (because of cutting) can be avoided. Based on the result, tool life of cutting tool was 920 cuttings.
Keywords
Full Text:
PDFReferences
Dewangga, dkk (2017). Pengaruh Variasi Kecepatan Putaran Mesin Bubut Terhadap Keausan Pada Alat Potong Pahat HSS Tipe Bohler MO 1/2x4. Jurnal Jurusan Pendidikan Teknik Mesin, 7 (1) : 1-10.
Nusa, dkk (2018). Pengaruh Sudut Geram dan Parameter Pemesinan Terhadap Keausan Tepi Pahat High Speed Steel (HSS) Pada Proses Bubut Glass Fibre Reinforce Polymer (GFRP). Jurnal Sistem Mekanik dan Termal, 2(1): 40-46.
Ibrahim, dkk. (2017). Analisa Keausan Pahat Pada Pemesinan Bor Magnesium AZ31 Menggunakan Metode Taguchi. Jurnal Teknik Mesin Indonesia, 12(1): 29-35.
Widiyono, E, dkk. (2011). Engineering Design of A Gang Drilling Machine Equipped with Jig and Fixtures to Make A Prototype Machine in Birdcage Production. IPTEK (The Journal for Technology and Science), 22 ( 4): 214-220.
Waluyo, J. (2010). Pengaruh Putaran Spindel Utama Mesin Bor Terhadap Keausan Pahat Bot dan Parameter Pengeboran Pada Proses Pengeboran Dengan Bahan Baja. Jurnal Teknologi 3 (2): 138-144.
Aswinur, dkk. (2017). Analisa Umur Pahat dan Biaya Produksi Pada Proses Drilling Terhadap Material S40C, Jurnal Polimesin 15(1): 1-7.
Nugroho dkk. (2018). Pengaruh Pemesinan Milling Terhadap Kekerasan Permukaan Baja Tahan Karat Martensitic Modifikasi AISI 410 3Mo – 3Ni Dan Keausan Material Cutter End Mill. Metalurgi, 33 (3): 145-152.
Ibrahim, dkk. (2017). Analisa Keausan Pahat Putar Pada Pembubutan Magnesium AZ31 Menggunakan Udara Dingin Bertekanan. Prosiding SNTTM XVI, hal. 6-10.
Ibrahim, dkk. 2017. Analisa Keausan Pahat pada Pemesinan Bor Magnesium AZ31 Menggunakan Metode Taguchi. Jurnal Mechanical, 8 (2): 71-78.
Bayuseno, A.P. (2010). Kajian Pustaka Tentang Keausan Pada Pahat Bubut. ROTASI, 12 (2): 38-41.
Sastal, A,Z, dkk. (2018). Pengaruh Kecepatan Potong terhadap Perubahan Temperatur Pahat dan Keausan Pahat Bubut Pada Proses Pembubutan Baja Karbon Sedang. ENTHALPY - Jurnal Ilmiah Mahasiswa Teknik Mesin, 3 (1): 1-11.
Ribowo, dkk. (2018). Pengaruh Sudut Penyayatan Endmill Cutter Dan Arah Pemakanan Terhadap Keausan Endmill Cutter Pada Pengefraisan Baja ST 40. Jurnal Kompetensi Teknik, 10 (1):52-58.
Nugroho, T, U. (2012). Pengaruh Kecepatan Pemakanan dan Waktu Pemberian Pendingin Terhadap Tingkat Keausan Cutter End Mill HSS Hasil Pemesinan CNC milling Pada Baja ST40. NOSEL 1 (1): 79-89.
Mulyadi, I, H. (2015). Kontribusi Pengaruh Kekasaran Permukaan dan Keausan Pahat Terhadap Konsumsi Energi Listrik Langsung Pada Proses Pemesinan Dingin dan Kering: Studi Kasus Proses Skrap Baja ST 37 (Baja Karbon Rendah). JURNAL ILMIAH TEKNIK MESIN CYLINDER, 2 (1): 1-10.
Patel, D, dkk. (2015). Analysis of Drilling Tool Live – a Review. Internasional journal of Mechanical Engineering and Robotics Research, 4 (10): 523-539.
Budiman, H, dkk. (2007). Analisis Umur dan Keausan Pahat Karbida Untuk Membubut Baja Paduan (ASSAB 760) Dengan Metoda Variable Speed Machining Test. JURNAL TEKNIK MESIN, 9 (1): 31 – 39.
Nurhadiyanto, D. (2010). Analisis Pahat Insert Bermata Potong Ganda Untuk Mengurangi Keausan Pahat Pada Mesin Bubut. Prosiding Seminar Nasional Sains dan Teknologi, Fakultas Teknik Universitas Wahid Hasyim Semarang, hal : 5-10.
DOI: https://doi.org/10.33373/profis.v8i2.2796
Refbacks
- There are currently no refbacks.
Copyright (c) 2020 PROFISIENSI
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
E-ISSN 2598-9987
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
PROFISIENSI: Jurnal Program Studi Teknik Industri
Building A, 1st Floor, Faculty of Engineering, University of Riau Kepulauan
Jl. Pahlawan No.99, Batu Aji, Batam, Kepulauan Riau
Email: Profisiensi@journal.unrika.ac.id