ANALISIS CACAT MENGGUNAKAN METODE FTA DAN FMEA PADA DEPARTEMEN BUFFING UNTUK MENURUNKAN JUMLAH UNIT CACAT (Studi Kasus : PT.BWB)
Abstract
The research was conducted to determine the factors - factors that cause defects in products, and provide corrective suggestions on how to improve the quality of the product Bracket SLM 315 which is currently still exceed the standards set for the maximum defect is 1% per month . The problem approach used is using Pareto diagram tools, then using the method Fault Tree Analysis (FTA) and methods Failure Mode and Analysis (FMEA) and 5W + 1H tools. From the results of data processing using Pareto diagrams, it is found that the dominant type of defect is defects under size, then the analysis uses the Fault Tree analysis method and the method Failure Mode And Effect Analysis which is the priority for improvement, namely the quality of the material. with the causes of the lack of inspections in materials raw parts and priority improvements based on the value of the RPN biggest that operator does not carry out inspection of goods raw part advance with a value of 336, the proposed improvements using 5W + 1H is Making special tools / pin to be used operator to check raw parts and own workReferences
Gusti, M. F. and Budiawan, W. (1996). ANALISIS PENYEBAB CACAT MENGGUNAKAN METODE FTA DAN FMEA PADA DEPARTEMEN FINAL SANDING ( Studi Kasus : PT . ABC , Semarang ), pp. 1–9.
Juliansyah Noor, S.E., 2016. Metodologi Penelitian: Skripsi, Tesis, Disertasi & Karya Ilmiah. Prenada Media.
Kartika, W.Y., Harsono, A. and Liansari, G.P., 2016. Usulan Perbaikan Produk Cacat Menggunakan Metode Fault Mode and Effect Analysis dan Fault Tree Analysis Pada PT. Sygma Examedia Arkanleema. REKA INTEGRA, 4(1).
Prasetyawati, M., 2014. Pengendalian Kualitas Dalam Upaya Menurunkan Cacat Appearance Dengan Metode Pdca Di PT. Astra Daihatsu Motor. Prosiding Semnastek, 1(1).
Risky, A. (2019). Analisis Penyebab Cacat Produk Menggunakan Metode Failure Mode and Effect Analysis ( Fmea ) Pada Pt . Sinar Sanata Electronic Industry. Skripsi Oleh : Risky Ardyansyah Fakultas Teknik Universitas Medan Area Medan.
Setyadi, I. (2013). Analisis Penyebab Kecacatan Produk Celana Jeans Dengan Menggunakan Metode Fault Tree Analysis (Fta) Dan Failure Mode and Effect Analysis (Fmea) Di Cv Fragile Din Co, pp. 1–78.
Yuwono, M.A.B. and Riyadi, A.S., 2013. Proses Produksi dan Pengendalian Kualitas Produksi Cat Plastic Coating Di PT Propan Raya ICC. Penelitian dan Aplikasi Sistem dan Teknik Industri, 9(2), p.182868.
Juliansyah Noor, S.E., 2016. Metodologi Penelitian: Skripsi, Tesis, Disertasi & Karya Ilmiah. Prenada Media.
Kartika, W.Y., Harsono, A. and Liansari, G.P., 2016. Usulan Perbaikan Produk Cacat Menggunakan Metode Fault Mode and Effect Analysis dan Fault Tree Analysis Pada PT. Sygma Examedia Arkanleema. REKA INTEGRA, 4(1).
Prasetyawati, M., 2014. Pengendalian Kualitas Dalam Upaya Menurunkan Cacat Appearance Dengan Metode Pdca Di PT. Astra Daihatsu Motor. Prosiding Semnastek, 1(1).
Risky, A. (2019). Analisis Penyebab Cacat Produk Menggunakan Metode Failure Mode and Effect Analysis ( Fmea ) Pada Pt . Sinar Sanata Electronic Industry. Skripsi Oleh : Risky Ardyansyah Fakultas Teknik Universitas Medan Area Medan.
Setyadi, I. (2013). Analisis Penyebab Kecacatan Produk Celana Jeans Dengan Menggunakan Metode Fault Tree Analysis (Fta) Dan Failure Mode and Effect Analysis (Fmea) Di Cv Fragile Din Co, pp. 1–78.
Yuwono, M.A.B. and Riyadi, A.S., 2013. Proses Produksi dan Pengendalian Kualitas Produksi Cat Plastic Coating Di PT Propan Raya ICC. Penelitian dan Aplikasi Sistem dan Teknik Industri, 9(2), p.182868.
Published
2022-07-30
How to Cite
AFMA, Vera Methalina; SUMARYA, Edi; AMBATODING, Nirwan.
ANALISIS CACAT MENGGUNAKAN METODE FTA DAN FMEA PADA DEPARTEMEN BUFFING UNTUK MENURUNKAN JUMLAH UNIT CACAT (Studi Kasus : PT.BWB).
PROFISIENSI: Jurnal Program Studi Teknik Industri, [S.l.], v. 10, n. 1, p. 30-40, july 2022.
ISSN 2598-9987.
Available at: <https://journal.unrika.ac.id/index.php/jurnalprofisiensi/article/view/4329>. Date accessed: 15 feb. 2026.
doi: https://doi.org/10.33373/profis.v10i1.4329.
Section
Articles
Keywords
Fault Tree Analysis, Failure Mode and Effect Analysis, 5W + 1H.
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
PROFISIENSI uses an exclusive license agreement. The authors will retain copyright along with the rights for academic use, while Universitas Riau Kepulauan will be granted publishing and distribution rights.
Open-access authors retain the copyright of their papers, and all open-access articles are distributed under the terms of the Creative Commons Attribution License (CC-BY), allowing others to distribute and copy the articles as long as the original work is properly cited.
Users cannot represent authors as support for the adaptation of their articles and do not change articles in such a way as to damage the honor or reputation of the author.
