ANALISIS CACAT MENGGUNAKAN METODE FTA DAN FMEA PADA DEPARTEMEN BUFFING UNTUK MENURUNKAN JUMLAH UNIT CACAT (Studi Kasus : PT.BWB)

Vera Methalina Afma, Edi Sumarya, Nirwan Ambatoding

Abstract


The research was conducted to determine the factors - factors that cause defects in products, and provide corrective suggestions on how to improve the quality of the product  Bracket SLM 315 which is currently still exceed the standards set for the maximum defect is 1% per month . The problem approach used is using Pareto diagram tools, then using the method Fault Tree Analysis (FTA) and methods Failure Mode and Analysis (FMEA) and 5W + 1H tools. From the results of data processing using Pareto diagrams, it is found that the dominant type of defect is defects under size, then the analysis uses the Fault Tree analysis method and the method Failure Mode And Effect Analysis which is the priority for improvement, namely the quality of the material. with the causes of the lack of inspections in materials raw parts and priority improvements based on the value of the RPN biggest that operator does not carry out inspection of goods raw part advance with a value of 336, the proposed improvements using 5W + 1H is Making special tools / pin to be used operator to check raw parts and own work

Keywords


Fault Tree Analysis, Failure Mode and Effect Analysis, 5W + 1H.

Full Text:

PDF

References


Gusti, M. F. and Budiawan, W. (1996). ANALISIS PENYEBAB CACAT MENGGUNAKAN METODE FTA DAN FMEA PADA DEPARTEMEN FINAL SANDING ( Studi Kasus : PT . ABC , Semarang ), pp. 1–9.

Juliansyah Noor, S.E., 2016. Metodologi Penelitian: Skripsi, Tesis, Disertasi & Karya Ilmiah. Prenada Media.

Kartika, W.Y., Harsono, A. and Liansari, G.P., 2016. Usulan Perbaikan Produk Cacat Menggunakan Metode Fault Mode and Effect Analysis dan Fault Tree Analysis Pada PT. Sygma Examedia Arkanleema. REKA INTEGRA, 4(1).

Prasetyawati, M., 2014. Pengendalian Kualitas Dalam Upaya Menurunkan Cacat Appearance Dengan Metode Pdca Di PT. Astra Daihatsu Motor. Prosiding Semnastek, 1(1).

Risky, A. (2019). Analisis Penyebab Cacat Produk Menggunakan Metode Failure Mode and Effect Analysis ( Fmea ) Pada Pt . Sinar Sanata Electronic Industry. Skripsi Oleh : Risky Ardyansyah Fakultas Teknik Universitas Medan Area Medan.

Setyadi, I. (2013). Analisis Penyebab Kecacatan Produk Celana Jeans Dengan Menggunakan Metode Fault Tree Analysis (Fta) Dan Failure Mode and Effect Analysis (Fmea) Di Cv Fragile Din Co, pp. 1–78.

Yuwono, M.A.B. and Riyadi, A.S., 2013. Proses Produksi dan Pengendalian Kualitas Produksi Cat Plastic Coating Di PT Propan Raya ICC. Penelitian dan Aplikasi Sistem dan Teknik Industri, 9(2), p.182868.




DOI: https://doi.org/10.33373/profis.v10i1.4329

Refbacks

  • There are currently no refbacks.


Copyright (c) 2022 Universitas Riau Kepulauan

Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

E-ISSN 2598-9987

 

This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.


PROFISIENSI: Jurnal Program Studi Teknik Industri

Building A, 1st Floor, Faculty of Engineering, University of Riau Kepulauan

Jl. Pahlawan No.99, Batu Aji, Batam, Kepulauan Riau

Email: Profisiensi@journal.unrika.ac.id

 

Web Analytics Made Easy - Statcounter