ANALISIS PERAWATAN MESIN POMPA SENTRIFUGAL DENGAN METODE RELIABILITY CENTERED MAINTENANCE
Abstract
The pump is an energy conversion machine that can move fluid from one place to another through a piping medium by adding energy to the fluid being moved continuously. To find out or minimize the occurrence of pump damage, periodic maintenance is carried out. In the pump type 6P-4021-J which is used in the STG (Steam Turbine Generator) and BB (Coal Boiler) sectors, PT. PUSRI is affected by the dirty condition of the slurry caused by the presence of mud and other so the working efficiency of the pump decreases. Therefore, periodic and routine maintenance or cleaning is required. Maintenance policies that are corrective or reactive, systematic or scheduled, and Condition-Based, all aim to achieve the availability and reliability of equipment and systems by reducing maintenance costs. Reliability Centered Maintenance method is used to analyze the causes of failure with the results of decisions for system maintenance. The critical components of a centrifugal pump include; bearings, seal rings, and impellers. The highest RPN value is the bearing component of 96. The reliability value of the bearing component is 0.468 with an average repair time of 3.32 hours. The recommended maintenance action is to apply lubricant regularly. So that it can reduce wear, prevent corrosion, and control the temperature of the bearing.
Keywords
Full Text:
PDFReferences
J. Pranoto, N. Matondang, and I. Siregar, “IMPLEMENTASI STUDI PREVENTIVE MAINTENANCE FASILITAS PRODUKSI DENGAN METODE RELIABILITY CENTERED MAINTENANCE PADA PT . XYZ,” J. Tek. Ind. USU, vol. 1, no. 3, pp. 18–24, 2013.
R. Robie, “Usulan Penerapan Reliability Centered Maintenance pada Fasilitas Power PT H3I untuk Peningkatan Ketersediaan Jaringan,” J. PASTI, vol. VIII, no. 2, pp. 251–265, 2016.
E. Pourjavad, H. Shirouyehzad, and A. Shahin, “Analyzing RCM Indicators in Continuous Production Lines: A Case Study,” Int. Bus. Res., vol. 4, no. 4, pp. 115–123, 2011.
William, H. L. Napitupulu, and A. Ishak, “Rancangan Sistem Informasi Perawatan Mesin Pada Pabrik Crumb Rubber PT . HB,” vol. 1, no. 3, pp. 11–17, 2013.
R. Khasanah, “RELIABILITY-CENTERED MAINTENANCE (RCM) EVALUATION IN THE INDUSTRY APPLICATION, CASE STUDY: FERTILIZER COMPANY, INDONESIA,” J. PASTI, vol. X, no. 1, pp. 8–14, 2011.
Denur, L. Hakim, I. Hasan, and S. Rahmad, “Penerapan Reliability Centered Maintenance (RCM) pada Mesin Ripple Mill,” J. Integr. Sist. Ind., vol. 4, no. 1, pp. 27–34, 2017.
Masyhudi, A. Zayadi, and Basori, “Uji Fungsi dan Karakterisasi Pompa Sentrifugal,” J. Ilm. GIGA, vol. 17, no. November, pp. 94–98, 2014.
A. Kurniawan, “Karakteristik Pompa Sentrifugal Dengan Variasi Penambahan Jumlah Fin Pada Bilah Tipe Semi Open,” Otopro, vol. 15, no. 1, pp. 20–26, 2019.
Y. Kurniawan and Kusnandar, “Uji Karakteristik Pompa Sentrifugal Pada Cooling Hydronic System Menggunakan Refrijeran Ramah Lingkungan,” J. Teknol. Terap., vol. 4, no. 1, pp. 63–71, 2018.
G. Ranggatama and H. Pranoto, “Analisis Perancangan Pompa Sentrifugal pada Perancangan Shower Tester Booth di PT X,” J. Tek. Mesin, vol. 9, no. 2, pp. 88–95, 2020.
L. Hakim and Fahrizal, “Penerapan RCM Pada Sistem Distribusi Air di PDAM Pasir Putih Pematangan Barangan Kabupaten Rokan Hulu,” J. Aptek, vol. 4, no. 2, pp. 129–140, 2012.
DOI: https://doi.org/10.33373/profis.v10i2.4635
Refbacks
- There are currently no refbacks.
Copyright (c) 2022 Universitas Riau Kepulauan
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
E-ISSN 2598-9987
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
PROFISIENSI: Jurnal Program Studi Teknik Industri
Building A, 1st Floor, Faculty of Engineering, University of Riau Kepulauan
Jl. Pahlawan No.99, Batu Aji, Batam, Kepulauan Riau
Email: Profisiensi@journal.unrika.ac.id